Protecta Products - Protecta-Wall

	"Used your products to seal the tops of my vans. WOW!! It worked great. I was very impressed. Very user friendly."
	Jay S. Louisville, KY
	READ MORE TESTIMONIALS HERE!

Protecta-Wall is an elastomeric coating that adheres to new and existing walls and provides beautiful, long lasting protection against extreme weather conditions. It is an effective waterproof coating that is superior to other products currently on the market. Its ability to expand and contract provides a solution to peeling and cracking from weathering effects experienced with other coatings. Protecta-Wall possesses the advantages necessary to become an industry leader.

Benefits Of ProtectaWall

Ease of application

No primers needed

UV resistant

Watertight

Won·t peel or crack

Long lasting

Free Shipping within continental U.S. for Internet orders

Additional Volume Discounts
Orders over 50 gallon call for commercial pricing

Percent solids: 51%
Weight per gallon: 8.75
Viscosity: 98KU
Flexibility Range: -53f to +410f
Cure time: 10 to 24hours
Elongation: 350%
Tensile strength: 1100 psi
Resistance to:
   Oil: Good
   Chemicals: Good
   Water permeation: Excellent
Adhesive Quality: Excellent
Application Method: Brush, roller, spray
Flashpoint: 115f

PROTECTA-WALL APPLICATION SHEET

AREAS OF USE

      • Cinder Block
      • Brick, Stone, Tile
      • Stucco, Granite

SURFACE PREPARATION

Surface must be free of dirt, oil, grease, loose paint, mortar, and any other contaminants. New, glazed brick should have the gloss removed with a wire brush. New block and stucco should be allowed to dry at least 60 days at 75°F. Power washing is recommended to ensure proper bonding of coating. Fill any holes or cracks with Protecta-Sealer. Any large cracks should be covered with Protecta-Sealer or fabric.

APPLICATION

Protecta-Wall is ready for use as it comes from the container. Do not thin. In cool weather, material may thicken, requiring warming by interior storage. DO NOT HEAT! Apply coating only to dry surfaces.

Protecta-Wall may be applied by spray, brush, or roller. For spray application, use an 0.030-0.035 orifice. Applied most effectively by air, gasoline, or electric-powered airless spray units such as Graco Model 744 or Speedflo HydraM 4000. Equivalent equipment from other manufacturers may also be used.

Clean up equipment with mineral spirits.

Apply when temperature is 40°F and rising. Wash-off resistance is dependent on temperature . . . 3-4 hours at 70°F, 12 at 40°F. Do not apply over moisture or frost.

COVERAGE RATES

Apply Protecta-Wall at a rate of 2 gallons per 100 square feet. On more textured surfaces, apply at a rate of 3 gallons per 100 square feet.

On new block with no previous paint or coating, a coat of paint may be applied to the block in order to fill the voids and reduce the need for additional coats of Protecta-Wall.

PRODUCTS AND PROCEDURES DATA

SHIPPING INFORMATION

Our products are palletized according to the following quantities:

5 Gallon Pails	-	36 per pallet
1 Gallon Pails	-	45 cases per pallet
Sealer	-	1, 5, or 55 gallon pails

Coatings may be packaged in 55 gallon drums

All freight is shipped collect, but is allowed pre-paid on advance arrangements. All freight charges are based on shipment from our plants.

STORAGE

Store product with lid tightly sealed to prevent material evaporation. Do not store product near heat or open flame. The product will have a shelf life of one year, if the container has not been opened.

Material Safety Data Sheets are available upon request.

Note: Before applying Protecta-Products, be sure that the surfaces to be coated are structurally sound and that proper surface preparation has been completed.